1)
A saw used for finishing work should have fewer teeth per inch than 
one used for general purpose applications
      True              False

2)
A plumb bob is used to establish a vertical line.
      True              False

3)
A try square has an adjustable blade for transfering angles.
      True              False

4)
The size of a hand drill is determined by the capacity of its chuck.
      True              False

5)
A chaulk line is the easiest tool to use for marking curved lines.
      True              False

6)
The point of a plumb bob is always precisely below the point from 
which it hangs.
      True              False

7)
A nail set is used to drill holes for casing or finishing nails.
      True              False

8)
Sizes of of phillips screwdrivers range from No. 0 to No.4, with No. 
4 being the largest.
      True              False

9)
The ripping claw hammer is has a straight claw.
      True              False

10)
To reduce wear on a hacksaw blade, remove pressure on the return 
stroke.
      True              False

11)
The size of a claw hammer is determined by the weight of its head.
      True              False

12)
A multi-blade forming tool (surform) leaves a smooth finished 
surface.
      True              False

13)
A small backsaw should be used to cut curves.
      True              False

14)
The blade rotation of a radial arm saw is in the direction of the 
saw feed.
      True              False

15)
A tool's power switch should always be in the "off" position before 
the tool is plugged into an electrical outlet.
      True              False

16)
A circular saw is usedfor cuttingarcs and other circular features.
      True              False

17)
Work should be fed to a power tool only as fast as the tool will cut 
it easily.
      True              False

18)
Machine guards can be removed if they are in the way.
      True              False

19)
A ground fault circuit interrupter must be permanently wired. It 
cannot be used on extension cords.
      True              False

20)
A combination blade can be used on a portable circular saw for both 
crosscutting and ripping.
      True              False

21)
The blade of a saber saw should be in contact with the work when the 
tool is turned on.
      True              False

22)
A router bit revolves in a counterclockwise direction
      True              False

23)
When operating a tablesaw, stand to one side of the revolving blade.
      True              False

24)
When ripping short narrow pieces on a table saw, a push stick should 
be used.
      True              False

25)
Stock should be fed into a jointer against the grain.
      True              False

26)
Try squares hve blades _______ long.
      less than 6"
      6" to 12"
      18"
      18" to 24"

27)
A tool with an adjustable blade that is used for transferring angles 
is the __________.
      T- bevel
      marking gauge
      combination square
      wing dividers

28)
A hacksaw blade should be installed on the frame with the teeth 
pointing ___________ the handle.
      toward
      away from
      either toward or away
      All of the above

29)
The framing square is also called a ____________ .
      combination square
      try square
      rafter square
      T-bevel

30)
The part of a hammer that contacts a nail when driving it is the 
_________ .
      adze eye
      cheek
      neck
      face

31)
Edge tools, such as chisels, can be sharpened by ________ on an 
oilstone.
      honing
      lapping
      grinding
      facing

32)
When making deep cuts with a wood chisel, a ___________ should be 
usedto drive the tool.
      ball-peen hammer
      wood or rubber mallet
      claw hammer
      mason's hammer

33)
For safe operation of a power tool, you must _______________ .
      know how it works
      know the correct way to use it
      be wide awake and alert
      all of the above

34)
The size of a portable circular saw is determined by ____________ .
      the motor horsepower
      the largest blade it will accept
      its weight
      width of the kerf

35)
For safety when using a potable circular saw, depth of cut should 
beadjusted to the thickness of the stock, plus _______ .
      1/8"
      1/4"
      1/2"
      1"

36)
A saber saw is also refered to as a ____________ saw.
      portable electric jig
      builder's
      drywall
      none of the above

37)
One type of portable power sander is a _______________ sander.
      belt
      disc
      finish
      all of the above

38)
Portable routers can be used to cut ____________ .
      dados
      mortises
      dovetail joints
      all of the above

39)
Belt and finish sanders should always be moved ________________ of 
the wood.
      with the grain
      at an angle to the grain
      across the grain
      any of the above

40)
A saw with the motor and blade suspended above the work is called a 
___________ saw.
      circular
      radial arm saw
      panel
      table

41)
A radial arm saw can be used for _________________ .
      ripping
      crosscutting
      mitering and beveling
      all of the above

42)
the size of a belt sander is determined by the ___________ .
      width of the belt
      length of the belt
      size of the snder motor
      none of the above

43)
When using a radial arm saw, a ______ margin of safety should be 
maintained between the operator's hands and the path of the saw 
blade.
      1"
      6"
      12"
      18"

44)
When using a jointer, the stock must be not less than _______ .
      2"
      4"
      8"
      12"

45)
A ___________________ saw has pointed teeth that cut like a knife.
      keyhole
      crosscut
      rip
      back
      coping

46)
A ___________________ saw has large teeth for cutting through paper 
and gypsum.
      keyhole
      back
      rip
      coping
      drywall

47)
A ______________ saw has fine teeth and a thin blade for cutting 
curves.
      crosscut
      back
      rip
      coping
      drywall

48)
A ____________ saw has chisel-shaped teeth for cutting along wood 
grain.
      crosscut
      back
      rip
      coping
      drywall

49)
A ____________ saw has small teeth for fine cuts on interior 
woodwork.
      crosscut
      back
      rip
      coping
      drywall

50)
A _______________ has narrow, quick-change blades.
      keyhole
      crosscut
      back
      rip
      coping